Power in Flux

Search:

Type: Posts; User: Hugues

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    424
    Views
    72,624

    This guy has dissassembled Leaf cells, at 18:11...

    This guy has dissassembled Leaf cells, at 18:11 he says the shell is not that heavy.
    https://www.youtube.com/watch?v=WcqaAz1vjlo

    Looks like a messy job in my opinion.
  2. Thread: Swiss EV show

    by Hugues
    Replies
    3
    Views
    255

    Yes and i'll be there with the bike, hopefully...

    Yes and i'll be there with the bike, hopefully without rain.
  3. You'll probably need to ventilate your motor very...

    You'll probably need to ventilate your motor very well. I'm running 7.04:1 and I had to do the following:
    - add 12v radial blower to force air into the openings on the shaft side to ventilate rotor...
  4. Replies
    0
    Views
    253

    Zvexx P1 at the Monaco Supercar show

    ok boys, a little self promotion here,:cool:

    i'll be showing off my bike at the Monaco Supercar show this week from April 20th to 23rd 2017 in....well...Monaco:...
  5. Pretty cool build ! we have pretty much the...

    Pretty cool build !
    we have pretty much the same gear,
    can't you reach a ratio of 7:1 with this rear sprocket ? i have 7.04 with 176 tooth on wheel and 25 on motor

    watch out when you connect...
  6. Yes, forward pin as to be connected. But you...

    Yes, forward pin as to be connected. But you should have received all these instructions, didn't you ?

    You can find them in the Support section here:
    http://www.hpevs.com/

    There is also a...
  7. Hi, Motor characterization procedure is...

    Hi,

    Motor characterization procedure is attached, not very difficult but not straightforward either if it's your first time. You should ask the vendor of the controller and motor (if you purchased...
  8. Hi, First thing, be sure your wheel is off the...

    Hi,

    First thing, be sure your wheel is off the ground, or better, your motor is not connected yet to your wheel. I just wanted to be sure, i guess you already know this. WHen you play with the...
  9. Replies
    7
    Views
    973

    20'000 gbp out of 240'000 gbp and with 4 days to...

    20'000 gbp out of 240'000 gbp and with 4 days to go....
    they mention a price tag of 7199 euros...clearly this company has never put any vehicle on the market...
  10. Replies
    424
    Views
    72,624

    thanks for the explanation, i thought it was...

    thanks for the explanation, i thought it was needed to have one mid-pack, because i was reading about it in Orion manual, now i understand why they write about it.

    thanks
  11. Replies
    424
    Views
    72,624

    I like these 3d printed purple spacers/covers. I...

    I like these 3d printed purple spacers/covers. I just printed round spacers for mine and they were a pain during assembly of the pack.
    Are you selling your 3d file ? :p

    Also, i don't have a...
  12. Replies
    1
    Views
    360

    Is there a real picture of the bike somewhere on...

    Is there a real picture of the bike somewhere on their website ? I haven't seen it....
  13. Replies
    4
    Views
    619

    Shame on me :o It was indeed just a bad wire...

    Shame on me :o

    It was indeed just a bad wire on CAN low.

    I must say for my defence that the blinking LED on the charger sent me in the wrong direction, and the zero CCL byte on the CAN message....
  14. Replies
    4
    Views
    619

    Can't charge the bike anymore

    :confused:
    hi guys,

    Saturday i could charge the bike, no problem, sunday went for a ride, did not touch at all the configuration of BMS or charger or anything, then sunday i cannot charge the...
  15. Finally, i got the whole thing to work :cool: ...

    Finally, i got the whole thing to work :cool:

    On my Torque dashboard, i now have both the BMS and Motor/controller data. I cannot see the data in the 3rd party screen on the BMS PC interface,...
  16. ok, so i managed to upgrade my controller with...

    ok,
    so i managed to upgrade my controller with the flash file sent by HPEVS and set my parameters back, everything works normally as before.

    So i got the BMS option in the menu, i turned it on...
  17. So, I've been in contact with HPEVS, they sent...

    So,

    I've been in contact with HPEVS, they sent me a file and program so i could flash my controller to get the new functions like BMS,...and they sent me a .cpf file with all the parameters.

    I...
  18. Hey Matt, I always ran with HPEVS AC-XX and...

    Hey Matt,

    I always ran with HPEVS AC-XX and Curtis, so can't speak for other brands, sorry.

    Currently discussing with HPEVS to upgrade my controller OS to their latest version so i can activate...
  19. !! I just checked all my menu options, BMS is...

    !!
    I just checked all my menu options, BMS is nowhere to be seen.

    Where did you get these ?

    This is my OS version:

    7289
  20. ?? Which screen is this ? I only saw the screen...

    ??
    Which screen is this ? I only saw the screen for CAN parameters, screenshot below.

    That would be great if this is what's missing.

    7287
    That's the only screen i see about CAN in the Curtis...
  21. 1- yes it's working. I'm using the CAN2 bus from...

    1- yes it's working. I'm using the CAN2 bus from BMS, this is the one i use for my charger, i tested with my charger and it works. Today I also inserted the CANOP repeater on the CAN2 line between...
  22. no progress here, i attach a schematic of my...

    no progress here, i attach a schematic of my circuit, maybe someone could spot something i'm doing wrong.

    Here's a link to the support ticket i opened with the supplier, ...
  23. Update on this project, I'm having troubles to...

    Update on this project,

    I'm having troubles to establish connection using this CAN repeater:
    7273

    - I power the unit with a 11 volts separate battery
    - I connect the CAN high and low of my...
  24. but isn't the rpm of the rotor more or less...

    but isn't the rpm of the rotor more or less synchronised with the frequency of the stator ?
  25. Thanks for your input Noah. Now i have another...

    Thanks for your input Noah.

    Now i have another question, from the HPEV's PID that Orion BMS can broadcast, pictured below, all of them are clear for me, except for the HPEV Frequency PID.

    Which...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4