Power in Flux

Search:

Type: Posts; User: flo

Page 1 of 5 1 2 3 4

Search: Search took 0.00 seconds.

  1. Hi to me there is something wrong in your...

    Hi
    to me there is something wrong in your calculations.
    I think the motor could be choosen smaller.
    Why is there 60Nm of torque required? a 200cc 4 stroke might have what 20Nm? and usually gear...
  2. Replies
    2
    Views
    265

    Hi will be very intresting how you get all into...

    Hi
    will be very intresting how you get all into there.

    Good luck

    Flo
  3. Replies
    108
    Views
    19,977

    Hi well like any industrial country they want...

    Hi
    well like any industrial country they want you to buy new.

    Talk about customising a vehicle.. pia

    Greets

    flo
  4. Replies
    108
    Views
    19,977

    Bureaucrats

    you either love then or hate them :p
    Hi everyone,
    had some fun - depending of you defeinition of fun- today with the german authorities.

    Here is how it goes if you live in germany:

    new...
  5. Thread: WORX.VOR.EMC.v3.3

    by flo
    Replies
    5
    Views
    296

    Hi good to see you still tweaking an already...

    Hi
    good to see you still tweaking an already functioning bike.

    As you mentioned you wanted to lighten it:
    Would it not be possible to get 3 more cells into each box on the sides and thus get rid...
  6. Replies
    108
    Views
    19,977

    Big EV Grin

    Hi,
    got the bike almost done today, missing basically the CA and a new brace on lower fairing as this doesnt close all the way anymore.

    Took it for a very brief ride ( just down the road a few...
  7. Replies
    108
    Views
    19,977

    Its alive - first motor spin

    Hi
    all problems solved, got it to spin for the first time today;);)
    Only had to manually meassure the sin and cos and adjust parameters in the software and presto works first try:o

    Of course ...
  8. Replies
    108
    Views
    19,977

    Trouble shooting - advice

    Hi
    after returning from a climbing session i imediately went into the garage in order to get the motor to a first spin.
    Unfortunately not so ... tried 6hrs but still not a single rotation...

    OK ...
  9. Replies
    108
    Views
    19,977

    Hi again no pics.. had to redo some of the...

    Hi
    again no pics.. had to redo some of the wiring but now everything is connectet up;);)
    Hope to have a first spin of motor by tomorrow (from a 10S rc pack - don`t want to risk the drive pack...
  10. Replies
    108
    Views
    19,977

    Hi thanks for your support Just finished...

    Hi
    thanks for your support
    Just finished mounting it the way shown above...
    no pics yet as it was getting dark when done. But i will show the outcome. All save inside the tank and attached to...
  11. Replies
    108
    Views
    19,977

    Hi time for an update: Got nearly all the 12 V...

    Hi
    time for an update:
    Got nearly all the 12 V cables done new. minus the indicator lights and CA in cockpit and Contactor switch to controller.
    Been wondering for quite some time as how to...
  12. Replies
    108
    Views
    19,977

    Hi got the upper pack (10s) finished with sense...

    Hi
    got the upper pack (10s) finished with sense cables and fixed to the bike - no pic though :(

    Holder for the emergency cut off done:
    8217

    fits nicely:
    8218

    Now i had to get it not only...
  13. Replies
    108
    Views
    19,977

    Pwr on the controller pin 7 should come live and...

    Pwr on the controller pin 7 should come live and close contactor of motor pack only after key switch is closed
    and the "e-stop" on handlebar is closed. I called it contactor on switch)
    Otherwise...
  14. Replies
    108
    Views
    19,977

    Wiring sheme anyone cares to have a look ?...

    Wiring sheme

    anyone cares to have a look ?
    hope its all really visible.
    Most important to me is the former indicator light that i have circled into that blue oval.
    Will this indicator light be...
  15. Replies
    108
    Views
    19,977

    better view 8210

    better view
    8210
  16. Replies
    108
    Views
    19,977

    HI never waste any material ;) 8208 Half of...

    HI
    never waste any material ;)
    8208

    Half of the chain guard done...
    would be finished by now if i was one to stick to his own plans..
    used up the other motor-cut-out to mill those stops for...
  17. Replies
    20
    Views
    1,450

    Hi welcome here. Always great to hear about new...

    Hi
    welcome here.
    Always great to hear about new projects.:)

    Sounds doable but as Andrew suggests check out LiFePo4 Batts for motor and aux.bat.
    2kwh should be doable still.
    also i would...
  18. Replies
    108
    Views
    19,977

    Hi Fuse(es) arrived, but my buddy being sick i...

    Hi
    Fuse(es) arrived, but my buddy being sick i am still waiting for the sens-wiring.
    In the meantime i got some open tasks done:
    -new break fluid
    -pre-alligned the motorplate in relation to...
  19. Replies
    108
    Views
    19,977

    More mockups.. trying out the new cockpit layout...

    More mockups..
    trying out the new cockpit layout atm... needs to be rotated a little more but otherwise i quite like it.
    greets
    flo
  20. Replies
    108
    Views
    19,977

    Hi all got the bike up into the garage, Motor...

    Hi all
    got the bike up into the garage, Motor craddle in all screws Locktided, controller and lower battery clamped in place (detail pics follow as i still need to do the sens wiring..)
    - rock...
  21. Replies
    108
    Views
    19,977

    Hi Frontend almost done.:) Forkseals and new...

    Hi
    Frontend almost done.:)
    Forkseals and new oil , Wheel back n.
    Cycle analyst arrived too so once my new tray for the upper pack is done it will be time for final assembly.:)
    Oh and still...
  22. Replies
    108
    Views
    19,977

    HI been thinking about it and even asking...

    HI
    been thinking about it and even asking around..
    Any product to recommend?
    Yes bus bars definetly on the big side but learning from Ripperton in a YT vid , that cooling of the pack is best done...
  23. Replies
    108
    Views
    19,977

    Hi all, guess its time for an update. Finished...

    Hi all,
    guess its time for an update.
    Finished the battery connections and boxes. ;). Took a while, not only for being lots of work but also, as its quite intimitating i opted to do only 2s (3P so...
  24. Replies
    108
    Views
    19,977

    HI after having too much trouble with the tiny...

    HI
    after having too much trouble with the tiny 1mm trunches in 3 mm aluminium i changed to 1,5mm thickness material and finally got the "lower bus-bars" made
    Instead of doing multible 2s3p...
  25. Replies
    8
    Views
    5,276

    Hi just seen this so i would like to comment....

    Hi
    just seen this so i would like to comment.
    First off plywood is very good to mill - i mill it basically all day long and have none of those "frizzles" like you. For that you have to get your...
Results 1 to 25 of 114
Page 1 of 5 1 2 3 4