Power in Flux

Search:

Type: Posts; User: milton

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Anybody have any idea if the clutch works in 1238...

    Anybody have any idea if the clutch works in 1238 controller? I have wired the clutch and checked the 12v supply. When i press the clutch the 12v is activated, but the motor does not stall.
  2. I figured out the Domino throttle wiring. The...

    I figured out the Domino throttle wiring. The wiring should be as attached. Now trying to workout the clutch. I took a short ride on the bike and it runs nice and smooth
    7404

    ...
  3. Alright. Ill do that and get back

    Alright. Ill do that and get back
  4. bought it at electricmotortsport ...

    bought it at electricmotortsport

    http://www.electricmotorsport.com/domino-twist-grip-throttle-with-microswitch.html
  5. I had a user programmer and configured it to use...

    I had a user programmer and configured it to use a three wire pot, I had bought a 3 wire potentiometer from amazon and used that to test run the motor few months ago before reselling the programmer....
  6. The throttle is working fine now. There are two...

    The throttle is working fine now. There are two green wires for micro-switch that needs to be connected together for the throttle to send proper signal. Else it sends hight throttle signal
  7. I do not have a programmer handy but it did work...

    I do not have a programmer handy but it did work with a another potentiometer with a three wire with a high, middle and low connection. I did not try with the domino throttle earlier
  8. Pin 15, 16 and 18 If I want to do a 2 wire...

    Pin 15, 16 and 18

    If I want to do a 2 wire throttle what pin should i use? Domino has a two wire configuration also. They also have two wire for microswitch. I dont know what that is for though.
  9. has any one used the Domino or Magura throttle? I...

    has any one used the Domino or Magura throttle? I wanted to know the wiring with Curtis 1238. I wired it up yesterday,
    - white throttle wire to pot low on curtis controller (Purple and white wire)...
  10. Thread: dc-dc booster

    by milton
    Replies
    17
    Views
    1,707

    May be a stupid question, but can you provide...

    May be a stupid question, but can you provide some more info on how you would use it? Just curious. Since its DC to DC so it would need a DC source for Charging!
  11. Yes i got the Gates Carbon GT 1400mm length 8mm...

    Yes i got the Gates Carbon GT 1400mm length 8mm pitch. Here is the latest picture with the battries fit in. I have the batteries mounted but dont have a picture of that yet.

    Still working on the...
  12. Thinking of either keeping it bare metal finish...

    Thinking of either keeping it bare metal finish it a bit and just clear coat it or go with matte black and bronze. But there is a long time to for that...
  13. Thanks ken.

    Thanks ken.
  14. Yes Nando. I built every thing from scratch...

    Yes Nando. I built every thing from scratch including the front suspension and rear swing arm. Also trying to figure out the design for the handle bar since the entire bike is curve, would...
  15. I am keeping that ratio as an option. My pulley...

    I am keeping that ratio as an option. My pulley is from Gates and they have quite some options for drive side pulley. If needed I can replace the drive side with a smaller one.
  16. Thanks podolefsky

    Thanks podolefsky
  17. Thans Frodos and Huges. I was worried the motor...

    Thans Frodos and Huges. I was worried the motor might be a bust as it was on the motorcycle when i welded few tacks

    Pictures attached. Still have a long way to go to get it road worthy. Pulley...
  18. Finally got the Motor to spin. Seems like i did...

    Finally got the Motor to spin. Seems like i did not connect the interlock wire to 12v. I tried connecting but the controller gave fault code 28. Tried it again today and it worked.. Motor has a spin....
  19. I received an email from evwest (the vendor) that...

    I received an email from evwest (the vendor) that i have to connect pin 22 (yellow wire for fwd) to 12v wire on pin 25 and pin 9 to a charger interlock. I dont have a charger connected yet, so i left...
  20. Huges, Motor is not connected to the wheel so...

    Huges,

    Motor is not connected to the wheel so no worries on that end.

    - Have you (or your vendor) ran the motor characterisation procedure ? since i understand this is a new motor and...
  21. AC-23 Motor not spinning with Curtis 1238 controller

    I Just finished wiring the motor controller Curtis 1238 with my AC-23 motor and batteries. The batteries are currently at 3.8v each building up at 92.4v and 120ah.

    The Controller status LED is...
  22. Replies
    10
    Views
    3,467

    Wouldn't the 7.04:1 ratio reduce the overall...

    Wouldn't the 7.04:1 ratio reduce the overall speed of the bike? The motor will have to run at higher RPM to achieve 60-80mph at 7.04:1 ratio then it would at 2:1 or 4:1. Just wondering.
  23. Replies
    10
    Views
    3,467

    Thanks Huges. Would you mind if you have a...

    Thanks Huges.

    Would you mind if you have a plan that you can share to make the pulley?
  24. Replies
    10
    Views
    3,467

    Did you get to try with the Harley pulley or its...

    Did you get to try with the Harley pulley or its based on assumption that the motor will get hot? Custom building that big pulley will be expensive :(
  25. Replies
    10
    Views
    3,467

    Thanks Huges. Are you running a standard harley...

    Thanks Huges. Are you running a standard harley rear pulley or one from gates as well? The belt seems to be .83" while a standard harley pulley will be more then 1" if i am not mistaken
Results 1 to 25 of 41
Page 1 of 2 1 2