Power in Flux

Search:

Type: Posts; User: jhaggerty

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    1
    Views
    906

    Bump

    Bump
  2. Replies
    1
    Views
    906

    11KWh 115V battery pack $1500

    Located in Sn Jose CA, this 7 module Gen 4 leaf pack has seen little use only between 20-80% and has a BMS. You can see where it was used in my build thread about the electric RF600.

    Selling...
  3. Replies
    3
    Views
    1,578

    Controller has been sold. Motor still for sale.

    Controller has been sold. Motor still for sale.
  4. Replies
    3
    Views
    1,578

    It was used for this build...

    It was used for this build https://elmoto.net/showthread.php?t=4872. I rode it for about 2000 miles before getting a production EV. The brush pack has been replaced on the motor and I have a spare...
  5. Replies
    3
    Views
    1,578

    Kelly 600A controller and ME1003 Motor

    I have a good condition Kelly 600 A controller and Motenergy ME1003 motor for sale in SF Bay Area CA. $800 takes the pair. Local pickup is preferred, but if you arrange shipping I will ship.
    ...
  6. Replies
    3
    Views
    4,016

    Zero motor is sold. ME motor and Kelly are still...

    Zero motor is sold. ME motor and Kelly are still available and batteries are still available.
  7. I realized today that I left this thread hanging....

    I realized today that I left this thread hanging. After the new batteries arrived last year I swapped them out with the 1st gens by splitting one of the double modules in half. I've got pictures...
  8. Replies
    3
    Views
    4,016

    Zero 75-5 Motor

    I have a Zero 75-5 motor for sale in the Bay Area California. I've shifted to riding production bikes (2021 Energica SS9+ :D ) and am hoping to find someone who will make a cool project out of this....
  9. New Batteries!

    Christmas came early this year yesterday as I heard the rumble of a freight truck outside:
    ...
  10. Thread: Yamaha Fazer

    by jhaggerty
    Replies
    4
    Views
    7,546

    I know this is way late, but what type of range...

    I know this is way late, but what type of range were you getting with your 13 leaf modules before the controller blew up?
  11. Some updates: The bike now has over 500 miles...

    Some updates:

    The bike now has over 500 miles on it with an average wh/mile of around 130. Only minor issues so far (crossing my fingers it stays this way) like the chain falling off from being...
  12. Replies
    1
    Views
    2,080

    They look awesome. Incredible to me that they fit...

    They look awesome. Incredible to me that they fit almost an entire 1st gen leaf size battery in there! (21kwh vs 24kwh in the leaf)
  13. 16.6 kwh of Nissan Leaf Gen 4 batteries (2018) 1.66kwh per module lot of 10

    Hello All,

    I will have 10 2018 nissan leaf modules for sale sometime next week (keeping 2 sets of 7 for personal use). These are larger capacity than the Gen2's (56 Ah per cell vs 33 Ah per cell...
  14. So I hit a deer yesterday. That sucked. Luckily...

    So I hit a deer yesterday. That sucked. Luckily the bike was mostly okay, just a broken right peg bracket, bent handlebar and some scraping. After that incident I went ahead and ordered an inertia...
  15. I've spent the past few days reconfiguring the...

    I've spent the past few days reconfiguring the battery mounting orientation. The orientation shown in the pictures before gave about 7 inches of ground clearance and a width of 7 inches from the...
  16. Replies
    6
    Views
    5,724

    How is your project going, Zero_Phobia?

    How is your project going, Zero_Phobia?
  17. Ended up ordering a custom 420 sprocket from PBI...

    Ended up ordering a custom 420 sprocket from PBI sprockets based on a JTR829 based on input from EV Ed. It wasn't too expensive, and they emailed me shipment notice only about 2 hours after I put in...
  18. Thanks Steve! I’m considering using an ANSI #50...

    Thanks Steve! I’m considering using an ANSI #50 roller chain for gearing checking purposes. Right now the front sprocket is for #40 anyway and I can get a steel 60 tooth sprocket and mill out the hub...
  19. What I could use some input on is the effect that...

    What I could use some input on is the effect that my tall gearing may be having on amperage to my motor and overall efficiency. When we were doing this for the school project I did some rough...
  20. Hey all, I have some major updates. Since I...

    Hey all, I have some major updates. Since I couldn't figure out photo hosting before, I gave up on updating this thread. Additionally, professors at school were being a PITA about approving our...
  21. Dad helping me lay out the mounting plate made...

    Dad helping me lay out the mounting plate made out of an aluminum drawer. ...
  22. https://lh3.googleusercontent.com/Wy-O0RYf5hkltjWZ...

    https://lh3.googleusercontent.com/Wy-O0RYf5hkltjWZ7VLB_Iq6thsjSrxbhVh8Ze_MJ1xf07d1lArdH uvSufKrt6u5NFKGGhrK0Rl8HRT93eVncRRNExrDHv3E4Nn8j2_ cteG3c1ZORUlgGzktzlIPTnawq0uxY8Bss4o=w2400

    This is the...
  23. Some photos from the battery box build. ...

    Some photos from the battery box build.
    ...
  24. Replies
    0
    Views
    5,464

    Wanted: 120V PMDC controller

    Hey folks,

    Iím in need of a controller that can handle 115V and probably around 400 amps. Something like the Kelly KDH series or a Curtis controller. If you have something you no longer need that...
  25. Replies
    136
    Views
    85,602

    Sticky: Would anyone using an ME1003 that knows how to...

    Would anyone using an ME1003 that knows how to use this sheet mind posting what you have for your torque inputs? I'm quite confused as to what I should be putting in here.
Results 1 to 25 of 35
Page 1 of 2 1 2